This striking 51’ performance cruiser has beautiful lines and lovely sheer. She exhibits excellent performance, stability, and comfort, and is easily handled with her split-rig ketch sail plan.
This fast, luxurious, well-renowned Kaufman & Ladd design is considered one of the prettiest performance cruisers afloat. She is well suited for coastal cruising, ocean passages, and fun day sailing.
“Blue Skies” has been virtually rebuilt as new, 2016–2018.
This yacht meets or exceeds the specification and quality craftsmanship of newly launched models of the finest yacht builders.
Her fine sailing quality is a result of her:
Year Built: 1980
Rebuilt As New: 2016-2018
Designer: Kaufman & Ladd
Builder: Mao Ta, Taiwan
Rebuild: Custom, CT, USA
Rig Type: Ketch
Spars: Carbon Fiber
Displacement: 38,500 lb.
Ballast: 15,000 lb.
Keel: Fin, lead
Rudder: Carbon spade
Water Capacity: 180 gal. (1 x 80 gal. aluminum tank, 1 x 100 gal. aluminum tank)
Fuel Capacity: 200 gal. (2 x 100 gal. aluminum tanks)
Engine: 100 hp 2017 Yanmar 4JH 3HTE Diesel, 600 hours
Propeller: Varifold 4 Blade Folding Prop
Line Cutter: Sharkshaft Shaft Line Cutter
Fuel Filter: Raycor 7550 Dual Fuel Filter System
Oil Filter: Reverso 12 volt Automatic Oil Filter System
Refrigeration: Frigoboat D/C Powered Refrigerator/Freezer System
All new custom refrigerator/freezer boxes
House Electrical: 12 volt
Shore Power: 110 volt
Batteries: 2 x 8D Gel Cell House Batteries
Delta Dominator 12 V starting battery
Battery Monitoring: Link 2000 Battery Monitor
Balmar Smart Gauge
Inverter / Charger: Freedom 25 Xantrax Inverter/Charger
Regulator: Balmar 614 Voltage Regulator
Alternator: 200 Amp Alternator Fast Charging System
Solar Equipment: Power Boost Solar Controller
Solar Panels on Bimini
New stanchions, stanchion bases, and double lifelines
Horn & bell
VHF Fog Horn
ACR / AIS Category 1 Transponder
Westmarine LED search light
The hull, deck, and structure are very strong. The hull features solid hand-laid FRP/PVC foam composite with FRP-covered stringers and frames and a uniquely designed hull-to-deck joint.
Bulwark girder (tm): fiberglassed in place creating an extremely strong triangulated hull-to-deck structure.
Deck and cabin house: FRP composite, incorporating 3/4" Airex PVC foam core resulting in great strength with excellent moisture resistance.
New high-lift carbon fiber rudder: carbon fiber shaft maximizes performance and handling while being significantly lighter and stronger than the original FRP rudder.
New steering system: high molecular rudder bearings, pulleys, and custom Edson pedestal.
The interior has been completely rebuilt as new. All cabinetry has been replaced or customized. There are new teak and holly cabin soles, new headliners, new mattresses, new upholstery, and new lighting and fixtures. All woodwork is highly finished with varnish and paint, and is of the highest quality craftsmanship.
You enter the main cabin from the forward companionway. The galley is to port and the nav station is to starboard. The main salon is forward, with a C-shaped dining settee and table to port and opposing settee to starboard with outboard pilot berths. Aft is the owner’s cabin and en suite head. The forward area contains a cabin with double berth, a head, and a forepeak cabin.
Aft Owner’s Cabin
There are two entries to the owner’s stateroom – via a private cockpit companionway or through the aft 4-panel teak doorway off the galley. The cabin contains new teak bulkhead veneers, ash ceilings with custom fiberglass headliner, custom teak and holly sole, and custom cabinetry, 2018. There is a rug on the cabin sole.
To port is a large double bed with custom spring mattress and Ultrasuede cover, 2019. Lighting and ventilation are provided by a hatch over the berth, 2 red/white LED dome lights, 2 LED reading lights, a USB charging plug, and a 2-speed turbo fan.
The ample storage includes a large custom cedar hanging locker on the aft port bulkhead, large custom overhead lockers, an outboard storage shelf, a custom bureau with counter and drawers forward to starboard, a 4-drawer under-bunk compartment, and a binoculars rack.
There is an aft doorway to the private head.
Engine access: Aft of the companionway ladder is a large door to the engine room through the aft bulkhead.
New 316 s.s. chain plates
Raymarine remote autopilot control
Maxwell remote windless / thruster control
Frigoboat refrigerator and freezer compressors
Custom fuel tank controls
Custom Marinco battery controls
Bracket for cockpit table
8 ft aluminum boat hook
Access to custom water tank manifold
Access to water pressure system pump
Access to engine room via custom removable companionway ladder
Aft Owner’s Bathroom
The aft cabin has an en suite head. It was rebuilt with all new cabinetry and reconfigured to have a separate glass shower stall with granite walls and tempered glass door. The vanity has a granite countertop and there is an automatic toilet. There are overhead lockers.
Custom tempered glass shower with honeycomb granite walls
Custom Harken track door
Custom s.s. towel bars
Sealand Vacuflush toilet
Entering the main cabin from the forward companionway brings you to the portside galley. There is also access from the aft owner’s cabin.
The entire galley has been custom rebuilt as new. All of the woodwork and cabinetry is custom made with ventilation cut-outs. The countertops are special lightweight high-strength granite over honeycomb composite.
The U-shaped galley is the perfect configuration for cooking underway. Facing forward into the salon are twin stainless steel deep sinks with stainless steel faucets. A countertop and lockers are outboard. On the port side is a Force Ten 4-burner stainless steel gimballing propane stove with oven and broiler, fitted cutting boards, and hand railing. Aft is a large counter top over custom refrigeration and freezer compartments with overhead lockers.
Custom fiberglass headliner; custom s.s. over the stove
Custom Awlgrip white, 8-point star ventilated cabinets with teak edging
Custom granite and honeycomb fiberglass / aluminum composite counter surface
Glacier Bay R50 custom refrigeration / freezer compartments
Force 10 4-burner gimballing propane s.s. stove with custom cutting boards / restraints
Deep polished s.s. 2-compartment sink with Seagull freshwater filter
Scanvik s.s. faucet / sprayer
Custom carbon cutlery drawer with s.s. cutlery
Assorted plates, bowls, and glasses
Assorted pots and pans
Cooking knives and implements
S.S. 2-compartment garbage pail
Trident propane monitoring system with alarm
110 plug with LED courtesy light
Under-sink storage compartment with vented doors
Cabin sole rug
Custom teak hand rails
The nav station is to starboard of the main companionway ladder and faces aft. It has an athwartships double seat with backrest. The angled chart table has a hinged opening top to the storage locker beneath. A large hanging locker is inboard of the chart table. There are instruments, navigation, and communications equipment on the aft bulkhead over the chart table. Outboard of the seat and chart table are double bookshelves and a custom electrical distribution panel. All electronic instruments and navcom equipment was recently replaced in 2017.
Overhead custom fiberglass headliner with ash ceilings
Custom companionway ladder
Custom instrumentation compartments with s.s. hinged fold-outs
Weems and Plath quartz chronometer
Weems and Plath barometer
Raymarine auto pilot, 2017
Raymarine ST70, 2017
Raymarine E95 radar plotter below, 2017; E125 on deck
Fusion MS AV7001
Navionics electronic charts
Standard Horizon Matrix AIS GPS, 2017
ST 70 entertainment system, external speaker
Custom circuit breaker board
Profile Tank monitoring system
Link 2000R Battery monitoring system
Balmar smart gauge
Rule high water alarm
Intervac central vacuum and vacuum bags
12V DC plug
110 plug with LED courtesy light
R/W LED dome lights x 2
The expansive and beautifully varnished main salon is forward of the galley and nav station. To port is a C-shaped settee with backrest and a dining table. There is an opposing settee with backrest to starboard. Both settees have pilot berths outboard and above, storage drawers under both berths, and an overhead locker forward of the pilot berths. The dining table with special inlays is unique and folds out for additional seating.
There are two doors on the main bulkhead, one to port to the forward head and one to starboard to the forward cabin. Upholstery, cabinetry, cabin sole, lights, and hatches are new and highly finished in varnish.
Forward of the main salon is a guest cabin with a large double berth to port with overhead lockers and shelf. To starboard is a large 3-drawer bureau with counter and recessed hanging locker above. Forward of this is an adjustable pilot berth. Cabin sides have varnished ash ceilings. There are all new hatches, lights, upholstery, headliner, and cabinetry.
Custom fiberglass overhead with teak trim
Ash ceilings over insulation
Custom teak / holly sole
Starboard hinged custom honeycomb bunk with custom radius face
Custom pull out portside bunk with Ultrasuede, 2018
Custom teak cabinetry starboard with 6 drawers and 2 cedar-lined ventilated door faces
Custom cabinetry portside with bed linens
New teak bulkhead veneers with 2 panel doors, 2018
2 LED Brushed s.s. reading lights
2-speed turbo fan
110 electrical socket with LED courtesy light
3 overhead R/W LED 6” lights
Storage compartment in cabin sole
S.S. door latch
Port aluminum water tank with Profile monitor gauge
Teak face mast step surround with 2 s.s. tie rods and turnbuckles
200 ft braided anchor rode in storage bin
New 316 s.s. chain plates with backing plates and acorn nuts, 2004
Custom carbon fiber mast wire junction box
The fully rebuilt forward head has an automatic freshwater toilet outboard to port with a teak vanity forward. There is a stainless steel sink and faucet with a large locker above. There is a shower, stainless steel towel holders, and teak floor grating. All cabinetry, lights, hatches, headliner, and fixtures are new.
Custom granite countertop
Cedar lined custom cabinetry
Custom teak grating floor
Lavac Vacuflush toilet
Scanvik shower faucet
Scanvik stainless steel sink
Shower sump pump
Custom towel bars
Entering from the forward cabin are hanging adjustable carbon fiber and teak pilot berths. The port berth has Sunbrella storage lockers beneath. To starboard there is a 3-drawer teak bureau with counter and recessed hanging locker above. There are varnished ash ceilings. There is a large sliding hatch above.
Mattress with Ultrasuede cover, 2018
Awlgrip painted overhead ceilings, 2018
Custom teak and holly floor, 2018
New teak veneer bulkhead, 2018
Chain locker bulkhead, removable teak, 2018
Carbon fiber line-hanging bar, 2018
Custom carbon tube bunk with Dacron bin for spinnaker bag with 2 side pockets
Custom starboard locker with battery switch for thruster
Wireless windless and thruster controls
Side power 9.5 horsepower thruster, rebuilt 2018
Removable 2-panel teak door
R/W LED overhead light
Thruster / windless battery, new 2018
Custom starboard side wiring tube
The semi-flush deck has a low wedge cabin top that blends into the foredeck. There are wide side decks with inboard genoa and jib tracks. The entire deck was recently stripped, re-primed and re-painted with Awlgrip. All original hatches were replaced with new Bomar and Goiot hatches. Additional hatches have been added for superb ventilation and lighting. The side deadlights have been replaced with tempered glass. All exterior wood is freshly stripped and varnished. All deck fittings and deck hardware have been replaced with new.
There is a large comfortable cockpit aft with extra-long seats and a large bridge deck. The cockpit floor and seat tops are covered with new teak decking. There is a removable cockpit table. The cockpit companionway is a custom addition with a custom Bomar hatch and companionway ladder. There is all new canvas work including dodger and removable full cockpit enclosures.
The cockpit floor has been rebuilt as new and has a large removable section for extra access to the engine room below. The starboard seat has a large hinged opening hatch to the engine room as well. There is a custom Edson steering pedestal aft and the mizzen mast is located on the forward wall of the cockpit.
Custom anchor rollers, 2018
Delta 65 lb. s.s. anchor, 2018
Custom s.s. hawser pipes p/s
Bow cleats, s.s.
60 ft 3/8” s.s. chain with 200ft 8 braid 1/2” rode, 2018
Lewmar s.s. windless deck controls, 2018
Simpson Lawrence vertical windless, rebuilt 2018
LED running lights, 2017
1x19 lifelines, 2018
Custom s.s. spinnaker pole brackets
Lewmar trapezoidal foredeck hatch, new acrylic 2016
4 Manship 24x24 2-way s.s. hatches, 2017
4 custom faux teak fiberglass Dorades with Manship cast s.s. ventilators
Bomar 36x36 midships companionway hatch
24x24 companionway Bomar sliding hatch
Faux teak custom midship hatch enclosure with custom coaming cap
Harken staysail tracks
Water diesel and waste caps with octagonal winch handle configuration
Custom s.s. chain plates with chain plate covers, recaulked 2017
Custom tempered glass side ports x 4
6 Goiot deck hatches
Deck drain screens s.s.
Salt water wash down deck fitting s.s.
Custom G10 main mast collar with Spartite and canvas cover
Wichard dual titanium folding bow pad eyes
Custom s.s. mast grab rails x 2
Custom G10 midships cleat pads with teak face and s.s. cleats x 4
Harken jib track x 2 with Lewmar jib cars x 4
Harken big boat traveler control with Spectra line
Lewmar 44 main sheet winch
Custom Teak Deck Systems in cockpit area and companionway, 2005
Lewmar 65 primary winches x 2
Lewmar 55 secondary winches x 2
All winches rebuilt 2018
Sails and Rigging
The sail plan features a powerful high aspect ketch rig. This split rig configuration provides for excellent performance, easy sail handling, and quick sail area reduction by lowering the mainsail to go under the classic “jib and jigger” combination.
In 2017 the aluminum spars were replaced by super strong, Hall Custom carbon fiber spars including main mast, mizzen mast, main boom, and spinnaker pole. The added strength and reduced weight aloft allow for an increase of mainmast height by 2.5’ and increased stability as well as reduced pitching and rolling in a seaway. All deck and sail handling gear, running and standing rigging were replaced and upgraded.
Harken big boat jib roller furling with furl line lead block and fairleads
Harken 2 track head foil
Hall carbon fiber main mast, mizzen mast, mizzen boom, main boom, spinnaker pole, with rod rigging 2017
Spectra main halyard, jib halyards, spinnaker halyard, staysail halyard
Spectra topping lift
Spectra Triadic Stay
Dutchman for main, new 2017
Raymarine masthead wind instruments
Custom fiberglass flag staff with contained VHF antenna (lightweight VHF cable and UltraWhip antenna)
Lewmar halyard winches, 2017
Spinlock halyard locks x 4
Spinnaker track and bell
Lopolight, deck light and steaming light in custom carbon housing
Masthead Lopolight anchor / nav / strobe
Hall quick vang
Kinder mainsail cover
Hall carbon spinnaker pole with cover
Main boom bridle
Solar panels on bimini top 2018
Mizzen mast with spin lock lock-offs
Spectra topping lift
Spectra mizzen halyard
Spectra mizzen staysail
Raymarine radar 2017 with Scanvik swivel bracket
New Sunbrella dodgers and full cockpit enclosures with new Eisenglass
New Main: 2 Full Batten / 2 ½ Batten with Dutchman Furling & Batcars, 2016
New Mizzen: 2 Full Batten / 2 ½ Batten with Dutchman Furling & Batcars, 2016
The engine and all mechanical components were replaced in 2017 at which time the engine room was completely stripped and renewed with the latest and highest quality products.
The engine room can be accessed 3 different ways. The cockpit floor has a removable hatch for wide top access to machinery, the starboard cockpit settee has a hinged waterproof top allowing great access, and there is a large door behind the aft companionway ladder in the aft cabin.
Yanmar 4JH3HTE 600 hrs. diesel engine
Delta Dominator 12 V starting battery, 2018
2 8D house batteries, 2017
Freedom 25 Xantrex inverter / charger
Power boost 200 solar power controller
Showermate propane hot water heater
Racor 7550 MAX dual fuel filter
Balmar 614 voltage regulator
Balmar 200 amp alternator with serpentine belt & custom bracket with internal adjustment
Reverso 12 V oil change system
3-way explosion-proof LED lighting
Kinder industries custom sound down insulation with fire proof blanketing
All thruhulls Marelon
Custom Edson quadrant
Custom Edson tiller arm for autopilot
PYI Rudder bearings
Groco seawater strainer
Engine Room Turbo Fan with custom ventilation system
RayMarine autopilot control, 2017
Ground Tackle and Line Handling
Delta 65 lb. primary anchor, 200’ 8-plait nylon rode, 60’ 3/8” chain
Secondary anchor with 200’ anchor line
Pivoting Mantus s.s. Anchor Roller
Side Power 9.5 hp Bow Thruster
Fenders x 4 with custom name polar fleece fender covers
New deck cleats and chocks
10 ft. inflatable dinghy with Mercury 9.9 four-stroke engine, 2017
Winter covers for masts and booms
Winter boarding ladder
Custom elk hide turnbuckle covers Custom wheel cover Custom cockpit table case Cover for settee table
Spare zincs, prop changing equipment
Propeller removal gear
P.O. Box 752 Port Washington Blvd.
Port Washington, NY 11050