2020 Treeve DS247m

DIMENSIONS

Overall length: 7.5m (24'6")
Waterline length: 6.73m (22'3")
Beam: 2.65m (8'9")
Draught: 0.75m (2'6")
Underhung galvanised stew with bolted flange for prop removal. Bronze stuffing box, kicking rings and emergency tiller.

WHEELHOUSE

Rigid GRP with 10mm toughened glass windows

EXHAUST

Water injected system with diesel exhaust hose

FUEL CAPACITY

114ltr (25 gallons) minimum

BILGE PUMP

Driven by main engine. 25mm (1") clutch operated Jabasco bilge pump with pipes and boat side discharge

BALLAST

Metal punchings encapsulated in resin

STARTING

12volt electrical system with alternator and lead/acid battery

GEARBOX

Hurth, PRM or Borg Warner hydraulic 2:1 reduction gear

STERNGEAR

Bronze 38mm (1 1/2") dia shaft with stainless steel intermediate shaft (in fore wheelhouse arrangement). Bronze Propeller and stern tube. Cutlass or grease lubricated white metal bearings.

RECOMMENDED ENGINE

30 - 40hp

OPTIONAL EQUIPMENT

Navigation lights

Compass/GPS

Diaphragm hand bilge pump

Fore and aft galvanised fairleads, cleats, bitts etc.

25lb anchor, chain and mooring line

Boathook and scrubber

Mizzen mast, mast, sail, rigging and blocks (gaff type)

Safety gear: lifejackets, red star signals, sound signals, fire extinguishers

CONSTRUCTION

Hull lay-up

13oz laminate made up as follows:-

1 gel coat

1 x 1oz CSM and 6 x 2oz CSM

300mm (12") either side of keel reinforced to 23oz/sq ft by adding5x2oz CSM

Area within 380mm (15") of sheer line reinforced to 19oz.sq ft by adding 3x2oz CSM

Sheerline reinforced: Lay-up 2 x 2oz CSM

Keel joint reinforced 1 x 1oz CSM and 5 x 2oz CSM

Transverse frames 75x50mm (3x2") polyurethane expanded foam encapsulated by 3 layers x 2oz CSM, staggered and carried onto hull by a further 150mm (6") spaced at 460mm (18") intervals from transom

KEEL

Galvanised 100 x 12mm (4x1/2") steel strap with ugs to be extended to rise at sterm. Skeg iron 12mm (1/2")

STEM

Shaped galvanised stemband and steel cap to deck

CATHODIC PROTECTION

Zinc

RUBBER

75x50mm (3x2") Iroko bolted to hull and fitted with 28mm (1 1/2") galvanised convex bar

GUNWALES

100x32mm (4x1 1/4") hardwood with 25mm (1")  Iroko capping and protected from working beer by a 20mm (3/4") galvanised convex strip

BILGE KEELS

Approved hardwoods / Iroko 100x50mm x 1524mm long (4x2" x 5' long)

ENGINE BEARERS

75mm (3") x 1 1/2 x Engine length, encapsulated in GRP. Galvanised steel top plates

ENGINE BOX

Weathernight GRP with integral soundproofing

DECKS

20mm (3/4") Marine ply finished with non-slip 6oz GRP. Approved hardwood 100x50mm (4x2") beams with 100x64mm (4x2 1/2") main beams all beams sheathed in 6oz GRP

BULKHEADS

20mm 3/4" Marine ply bonded to hull

RUDDER - TIMBER OPTION

38mm (1 1/3") Iroo with 32mm (1 1/4") cheek pieces and suitably braced blade. All rudder fittings in galvanised steel.

 

FOR MORE INFORMATION, PLEASE CONTACT US

The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.